Compared to building materials, solar panels are expensive. This makes the entire building project very costly.

Homebuilders are usually very reluctant to suggest this idea to client unless they ask. They are afraid clients will go elsewhere. Homeowners are pretty ignorant about building integrated photovoltaics as well.

This doesn’t improve solar panel adoption rates at all. Thus solar panels are not commonly integrated into building structures.

Even though the energy yield of PV panels is not as high as separately-installed PV panels, their aesthetics are superior. Each building integrated PV panel’s energy output depends on its orientation, location, daily weather and season.

During summer, your PV panels can yield as much as 5 times the amount of electricity produced in winter. For example, your solar panels may be able to generate 500 watt-hours of energy in summer. However it only produces 100 watt-hours of energy in winter. Therefore preparation must be made for such trends.

A solar professional will be able to do a site analysis and let you know the energy output of the solar panels on your building through the seasons.

If you need to increase your energy production but are unable to due to space constraint, you can consider using solar trackers. These devices find out where the sun is and tilts the PV panels towards it.

Some manufacturers claim that solar trackers can almost double the power output of a solar array. However this is achieved only with increased cost and complexity.

You, the consumer, must make sure that your solar tracker purchase makes sense financially. And since mechanical parts are involved, there may be regular maintenance required. You must also be prepared to roll up your sleeves or get someone to do this.

As with all types of solar panels systems, a form of energy storage is required. If you’re using building integrated solar panels to serve as an off-grid power resource, then deep-cycle rechargeable batteries are a must.

Otherwise the lifespan of your batteries (which are not cheap) can be compromised. If you have a grid-tied (or intertie) PV system, shallow-cycle batteries may be acceptable although using deep-cycle batteries is still preferable.

Photovoltaic is still a relatively new technology. When they were just commercialized, solar panels were so expensive only NASA (and other large corporations) could afford them. But scientists have made significant efforts to lower its cost and increase its efficiency.

In the near future, we may see high quality solar panels that are as cheap as $1 per watt. When this is realized, building integrated solar panels will be a common sight.

Continue Reading:

1. Sizing Your Solar Energy Panels – Part 3
2. Creating An Energy Efficient House – A Primer On Why You Should Do It and How
3. How To Make A Solar Powered Air Conditioner

In general, climate has a direct influence on sunlight intensity. Different conditions (as listed below) may restrict or permit the use of solar panels on your property:

1. Sunlight.

The southwest part of the U.S. gets the most sun while the northern states (and Canada) gets the least.

Obviously if your area doesn’t have enough sunshine, it won’t be cost-effective to install solar panels. But how much is enough?

Studies show that the amount of sunlight we experience across the United States is more or less within 20% of the sunshine level in Florida. This makes it possible for most households to have solar panels on their roofs.

Occassionally, there may be shade issues at specific locations, but this can be solved in one way or another.

Generally, the more sun your home experience, the better (and faster) return you’ll have on your investment. You can get data about the sunshine your area experiences from the National Renewable Energy Laboratory (NREL). They recorded sunlight data on 239 locations all across the United States:

http://rredc.nrel.gov/solar/pubs/redbook/

2. Cloud

If you are living in a cloudy region, it is still possible to use solar panels. This is because solar energy is present although it’s diffused. Surprisingly, there is an advantage to this. The orientation of your solar panels becomes less important since light is coming from different directions.

3. Snowfall

Snow covers your PV panels and weighs them down. Some parts of your property may accumulate more snow than others. This may be because some spots are warmer than others. You will want to locate your solar panels where there is least snow accumulation.

4. Fog

Pollutants, fog and smog in the air affect sunlight intensity. If this is an obvious concern, you (or your contractor) should measure the sunlight intensity at your area to determine if you can get enough solar energy on a long-term basis.

5. Temperature

PV panels are affected by temperature. The lower the temperature, the better its performance. You can generally get more power output from a cold, cloudy day than a hot sunny day.

6. Air Density

Air density affects the amount of sunshine you receive. However its effect is marginal compared to the other factors. If you live on the mountains where air is thinner, you receive more sunshine. The air temperature may also be lower. Thus your PV panels will likely be more effective than when it’s installed at sea level.

7. Wind

Strong winds can damage your solar panel installation by tearing it from its mounts. But this, by itself, should not deter you from using solar panels.

To handle strong wind, you can either (i) use stronger mounts for your solar panels, (ii) use vegetation to block the wind, or (iii) use wind turbines to dissipate its force and to generate more electricity.

Some wind is actually good for solar panels. It helps to cool them down by bringing heat away. This helps to enhance its efficiency.

Continue Reading:

1. 7 Different Ways of Using Solar Energy At Home and In Your Office
2. Survey Your Household Energy Usage Before Installing Solar Panels
3. Before You Install Solar Panels, Plug All Your Air Leakages

So how do you know if building a do-it-yourself solar panel is the right thing for you?

There are a few guidelines that can help you along. In this way, you won’t ever have to get into a project just to abandon it mid-stream.

You should build your own DIY solar panel if:

1. You are able to work with simple tools and have a weekend to spare

Thankfully, all it takes to build a reasonably sized solar panel are simple tools and a weekend. If you have browsed through the free book titled “How To Build A Solar Panel”, you’ll understand it doesn’t take much. (Download it now, if you haven’t…)

This assumes you have already gathered all your materials and have them cut to size. In fact, if you already had some DIY experience, you can even build a solar panel (not the complete set to power your entire home) in an afternoon.

However do note that integrating your inverter and the battery bank into your power system certainly requires planning and installation. And this takes up time as well.

2. You are not willing to invest much into a solar power generator

Cost is the main reason people build their own solar panels. This is understandable. You can easily burn at least $20,000 (depending on the size of your house) to install a solar energy generator. And things are not getting any cheaper…

With homemade solar panels, you’ll only have to part with a fraction of this cost. This means you’ll get your returns on investment sooner. And your home may be worth a lot more than it originally was without spending a ton of money. In some states, you can receive tax breaks just by using renewable energy like solar power.

In terms of dollars and cents, it certainly makes sense to build your own photovoltaic panels.

Of course, there is no point in starting a DIY project if you simply have no time or are totally uninterested in picking up even a screwdriver to put the solar panel frame together.

Needless to say, if you have spare cash (to the tune of $20,000) to burn, it can be quite fun to watch the contractors climb onto your roof to slap on a few pieces of solar panels while you sit at your garden with a can of beer in your hand.

Seriously, you have to take some time to decide for yourself if building homemade solar panels is for you. Otherwise you can start a DIY solar panel project and leave it uncompleted, shelving it for years in your garage.

Continue Reading:

1. Homemade Solar Panels
2. Sizing Your Solar Energy Panels – Part 3
3. Solor Panel Inverters – Synchronous Solar Panel Inverters

Sealing Off A Crack

Before you install solar panels, you need to perform an energy audit.

This serves a two-fold purpose – to determine the size of your solar power generator and to identify sources of energy wastage that can be avoided.

As you are doing your household energy audit, it is useful to check for air leaks. They account for as much as 5 to 30 percent of your energy wastage (when it comes to heating).

If your windows and doors are closed and you feel an air draft, you have a good chance of cutting down wastage simply by plugging the leaks.

The best time to test for air leaks is when it’s cold outside and warm inside. You can feel cold air quite easily this way.

A pressure test can quickly surface any leakages around your house. All you have to do is close your doors and windows, turn off all heaters and turn on your exhaust fans to full blast.

In this way, the pressure inside your house is slightly lower than the outside. Thus more air will flow through those leakages to equalize the difference in pressure.

Go around the house and look for leaks. Pay more attention to windows, doors, electrical outlets, switches, hatches and joints. Once you find a leak, mark them out immediately.

Before you seal off those leaks, you have to turn off the exhaust fans.

You can use transparent silicon caulk to plug all your air leakages. The best way to handle this is to use a caulking gun that has a pressure relief gasket. This allows good control of silicon flow as you plug those leaks.

Another way to plug air leaks is to use an aerosol can of expandable insulation. This is difficult to use, initially, as it is hard to control its flow. But it works very well. So if it’s your first time using this, get some practice on used magazines.

There may be several places that leak air. Windows and doors are easy to handle. But if you have to climb up to your roof, remember to take precaution so you won’t risk falling.

After you’re done plugging up the leaks, repeat the pressure test. Then mark out those areas you have to work on again and get cracking.

You can also check for leaks outdoor. Most often, they appear in cracks, around faucets, pipes, electrical wiring and electrical outlets. Unfortunately there is no way you can feel for air leaks outside your house.

The only way to handle this is to do a visual inspection. If you suspect a leak, give that area a touch of silicon caulk.

After you are done plugging all your air leaks, your heating system can be more efficient. Thus your indoor temperature can be maintained using less energy.

Continue Reading:

1. About
2. Sizing Your Solar Energy Panels – Part 3
3. 7 Different Ways of Using Solar Energy At Home and In Your Office

Home Solar Power Systems

This article will paint a thirty thousand foot view of this plan and then discuss how we can implement it. Then I’ll let you in on further resources that will help you with solar energy calculations, construction and installation.

Building a home solar power system involves a few major steps:

(1) Determining the household energy requirement. This influences the number of solar cells needed to produce the required electrical energy.

Most households will not want to take their homes completely off-grid. After calculations, the majority of families seem to prefer their solar panels to bear roughly 75% of their total energy consumption.

Why do they not want their house to be totally off-grid and be 100% powered by green, renewable energy? Because there will be periods when the light intensity is insufficient. It’s during these times when we’ll need to tap into the grid again.

(2) Constructing the solar panel. The photovoltaic cells are responsible for converting solar energy into electrical energy. It is also a major cost driver. Therefore the solar panel is the most important piece of the puzzle.

If you’re on a budget, you’re able to construct a solar panel by joining broken solar cells together. If you have money to burn, buying ready-made, commercial solar panels can also be an option. These come with long warranty periods (like 25 years and beyond) and are framed in high quality aluminum.

(3) The inverter. This component converts direct current (DC) generated by the solar panels into alternating current (AC) that’s usable by your household appliances. After that, this is channeled to the power distribution box via a synchronizer so that electricity from the grid and electricity from the solar panels can be combined before each appliance in your home uses them.

(4) Installation. Obviously, we need to choose a location where there is as little shade as possible throughout the day. This is usually the roof. With proper guidance from more experienced hobbyists or a guidebook, you can fix the solar panels to your roof (or anywhere else) exactly like the professionals do.

To put all these together, you’ll need a proven plan that tells you exactly what to do — from the broad structure down to the last bolt and nut.

Continue Reading:

1. How To Build A Personal DIY Solar Power System With Less Than $99
2. Do-It-Yourself Solar Panels – Electricity Conversion From Sunlight
3. Homemade Solar Panels

1. Panel certification. This is a pre-requisite for federal and state rebates in the US. There are specific sets of standards that manufacturers must meet. These are some of the most widely used standards:

· IEC 61215 (for crystalline silicon)
· IEC 61646 (for thin films)
· IEC 61730 (safety, for all module types)
· UL 1703 (safety)
· CE mark (for EU regulations)

2. Flash Report. A flash test measures the power output in response to a short burst of xenon light source. The flash lasts for 1 to 30 milliseconds at a light intensity of 1 watt per Meter Square. The spectrum of the light source closely resembles the solar spectrum. The results in the flash report are then compared to the specifications of the PV module’s datasheet.

3. Series Fuse. Every solar panel has to be protected by a surge-protection device. This is to prevent unintended damage due to high currents leaking from neighboring panels.

Such condition (called backfeeding) occurs frequently whenever one series string of panels experience shading or has a damaged circuit. Series fuses are often located in the combiner box or in the grid-connected inverters.

4. Maximum Power Voltage. This is the voltage (V) when the output power is at its maximum. It is one of the important figures that must be considered when choosing a particular inverter or controller.

5. Maximum Power Current. This is the current (A) when the output power is at its maximum. This figure is usually needed in calculations for PV array disconnect labeling as required by National Electrical Code (NEC) Section 690.53.

Voltage Measurement

6. Open-Circuit Voltage. This is the maximum open-circuit voltage of your PV panel when it is exposed to sunlight. Note that no load should be connected while the measurement is done. Since the output voltage increases with lower ambient temperature, the open-circuit voltage is measured at the historic low temperature. This will determine the highest possible voltage output.

This rating is important for making sure your components (panels, wiring, inverters, charge controllers, electronics, etc.) are designed to take the maximum possible voltage.

7. Short-Circuit Current. This is the maximum current produced by your solar panel when short-circuited. It is important to ensure that fuses and breakers are rated to handle high current surge during such events. Thus this measurement must be done.

More important facts and properties of your solar panel can be found at the following links:

(i) Important Facts And Properties of A Solar (PV) Panel You Must Know About (Part 1 of 3)
(ii) Important Facts And Properties of A Solar (PV) Panel You Must Know About (Part 2 of 3)

Continue Reading:

1. Sizing Your Solar Energy Panels – Part 3
2. How To Build A Sun Tracking Mechanism to Increase Your Solar Panel Efficiency by 40%
3. Important Facts And Properties of A Solar (PV) Panel You Must Know About (Part 1 of 3)

This is the third and final part of the “Sizing Your Solar Energy Panels” series. Have you done some calculations for your future solar power system yet? If you have been doing those mini exercises, you’ll most likely find a suitable solar panel for your home by now.

The next step requires us to find an appropriate-sized battery bank, inverter and charge controller. Let’s look at each of these:

1. The Inverter

The inverter you choose has to be sized according to the demands of the alternating current (AC) side of the circuit. Therefore you will choose a specification according to the loads in your house (with a little buffer in case you increase your loads over time). Pretty straightforward.

2. The Charge Controller

You’ll at least need a basic charge controller to begin with. Until you get fussy about how advanced you want this component to be, more affordable models will do just fine. You’ll need to get a specification that fits the output current (Amps) of your solar panel arrays. If you intend to scale up your solar power generator, you’ll do better with a larger charge controller with room to accommodate more solar panels than with two smaller-sized ones.

3. The Battery Bank

The size of your battery bank depends on how you want to use your solar panels. You can size your battery banks such that it can get you through thick clouds that pass by, or you can size them so you can get through three solid days of solar eclipse and a power outage at the same time. It really depends on you. But take note that over-sizing isn’t always realistic. You have to take into consideration the space they occupy and the how much they’ll cost you.

If your home is grid-tied, provided there aren’t frequent power outages, the size of your battery bank isn’t critical. Just size it to take care of cloudy days will do. You can still maintain your lifestyle by drawing power from the grid.

When you design your battery bank, you’ll have less power loss (through wires) if the voltage is higher. If you are able to design a 48-volt system, you can conserve more power than when you use a 24-volt or 12-volt system.

Continue Reading:

1. DIY Solar Panels — Charge Controller Basics
2. Sizing Your Solar Energy Panels – Part 1
3. Sizing Your Solar Energy Panels – Part 2

Image via Wikipedia

There are two major benefits to using residential solar panels. First, you can reduce pollution as you rely less on the burning of fossil fuel. Second, you can get a very good return on investment on your photovoltaic panels — these are always double digit returns, much better than Wall-Street-types investment with only single digit paybacks.

Other than these two benefits, there are more that people seldom heard of. But these can be significant when added together:

1. Government subsidies

Many state governors have realized the importance of using renewable energy. Therefore rebates, tax breaks and subsidies are given to households that use renewable energy to power their homes. The total discount on a system may be more than you imagine…sometimes more than 50%. Therefore do check what you’re eligible for.

2. Electricity Bill Hedging

Fuel is consistently increasing in price due to inflation and diminishing supply. But whatever the cost of fossil fuel may be in the future, there is no need for you to pay an extra cent if your solar power generator can supply all your energy needs. The grand total of your bills will still amount to $0. Isn’t that great?

3. Property Appreciation

Properties installed with solar panels are worth more than those without. This is obvious, since solar power generators are assets that can help the household lower their monthly electricity bills dramatically. Having PV panels in your property will not increase your property tax. Therefore it is a priceless item that can maximize the value of your home.

When we install solar panels on our property, we always look for numbers like cost per watt or payback period.. With the above benefits such as government incentives and rebates factored in, we’ll find these numbers become more attractive. Moreover, there are also many intangible benefits like environmental protection that comes along with your PV “toy”.

Continue Reading:

1. Solar Energy Panels – What You Need To Know Before Purchasing
2. Cost Of Using Residential Solar Panels
3. Homemade Solar Panels – Should You Even Roll Up Your Sleeves To Build One?

There are obviously costs involved in setting up residential solar panels. Today, we’re going to look at these and balance them up with the financial gains you’ll experience. It’s a busy day, so let’s get right in:

Cost #1: Equipment.

Equipment forms the largest part of the entire solar power setup. These are PV panels, inverters, battery bank, regulators, et cetera. Equipment cost can be spread out over time if you want to expand your solar power generator over time. Perhaps your goal is to be able to build up one more solar panel every weekend. Thus your cost really spreads out over time. It can really be less taxing on your wallet this way.

Cost #2: Installation

If you want to do the installation yourself, you won’t have to worry about this cost. But if you want to get a professional or contractor to do it for you, remember o budget for this as well.

Cost #3: Interest

If you took up a loan to pay for your PV panels and other photovoltaic components, the interest is going to build up and this must be factored into the overall cost as well.

Cost #4: Permits, Fees and Taxes

In some locations, you’ll need to pay for permits and fees when you install solar panels over your roof or on your property. Generally, most states let you install solar panels without imposing taxes on them. But be sure to check with your local authorities so you know if you need to pay for any taxes.

Cost #5: Clearing Refuse

If you need someone to clear out any refuse for you, you may need to pay for their service.

Now these are all costs…how about the benefits, I hear you ask. Well, here are the financial gains you’ll enjoy:

Benefit #1: Lower Energy Bills

The most obvious benefit is the reduced (or eliminated) electricity bills. If you are adding solar panels gradually to your collection of “solar harvesters”, your energy bills will gradually reduce and may finally be eliminated.

Benefit #2: Hedge Against The Rising Cost of Energy

The cost of energy is set to rise as inflation and scarcity forces its price upward over the long term. We all experience this effect — everything seems to get more expensive! Yet when you’re tapping energy from the sun, it doesn’t get more expensive then when you first bought the photovoltaic equipment. Therefore while the rest of the world pays for electricity through their nose, you can quietly enjoy cheap electricity using solar panels.

Benefit #3: Appreciation

The price of your property will probably appreciate because you installed an asset. Depending on the valuation, you may get back what you paid for. This mean you’re really using all the energy for free through the years. If you built your own residential solar panels, you’re definitely going to get back more than you invested in equipment and other photovoltaic components.

Continue Reading:

1. Benefits Of Using Residential Solar Panels
2. Why Are Solar Panels The Best Investment For Your Home?
3. Residential Solar Panels — Reducing Your Carbon Footprint

Solar Panels Installation

Buying (or making) solar panels is an investment you make toward a better future. For every investment you make, you have to find out the risks involved and its potential payback.

This is the same whether you invest in equity, put your money in the bank or use it to buy a solar energy system.

Even if you know (or have an intuition) that investing in solar panels for your home is a great decision, it doesn’t hurt to estimate how this decision can help you financially.

First, let’s look at the big picture: There is an upfront cost for owning PV panels, and this hurts initially (for many of us, at least). Thankfully this is about all you’ll pay for the next 30+ years, as long as your solar panels last.

When you add up the total cost of your utility bills for the next 30+ years, your perspective will change. This is because it will almost always be more expensive. To make things worse, energy rate only goes skywards over time. And the bill you’re paying now will probably double in 30 years time.

Do you remember what the energy rates were 30 years ago?

Next, in order to know how long it takes to recoup your investment, we have to consider the total upfront cost for a commercial solar panel setup.

Here is a list of things you have to invest in:

1. Equipment cost. This includes your PV panels, inverters and rechargeable batteries, if applicable. This cost can be paid in one lump sum, or you can get financing from the bank or the supplier. When a loan is involved, you also have to include interests to the total cost.

2. Installation cost. You can hire a professional installer…or you can do it yourself, if you are handy with these tasks. Installers can charge you an hourly rate or quote you a net price for the installation job.

3. Maintenance cost. You’re lucky…solar panels need very little maintenance. And damages are usually paid for by the warranty.

4. Miscellaneous costs. There are other costs involved. You may have to pay for permits and fees to carry out solar panel installation on your roof. Although rare, there may also be taxes involved as the value of your home appreciates due to solar installation. When your solar panel has reached the end of its lifespan, you may also have to pay people to haul your equipment away.

Fortunately, the costs above are defrayed by subsidies and rebates that you may be qualified for. Your utility company, the state and federal government or even the manufacturer often provide these benefits.

Part 2 of this series talks about how long it takes to recoup your investment in the light of the above costs. The article also illustrates how much savings you can expect by installing solar panels at home.

Read on…

View Part 2 here:

http://www.diysolarpanelsworld.com/how-to-determine-the-payback-for-your-solar-panel-investment-part-2-of-3

Continue Reading:

1. Building A DIY Solar Panel – My Personal Experience
2. Why Are Solar Panels The Best Investment For Your Home?
3. Survey Your Household Energy Usage Before Installing Solar Panels